Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
sliding_plates_replacement [2020/02/09 23:58] – joachim | service:service_instructions:sliding_plates_replacement [2020/09/18 02:00] – joachim | ||
---|---|---|---|
Line 3: | Line 3: | ||
This instruction will guide you on how to replace the sliding plates. | This instruction will guide you on how to replace the sliding plates. | ||
- | Sliding plates are a wear part that needs to be replaced when symptoms occur. For how long one pair of sliding plates last is all idividual | + | Sliding plates are a wear part that needs to be replaced when symptoms occur. For how long one pair of sliding plates last is all individual |
- | For more detailed information regarding the sliding plates, go to exploded view: [[:telescope_assembly|Wide sliding plate]] and [[:middle_beam|Narrow sliding plate]]. | + | For more detailed information regarding the sliding plates, go to exploded view: [[:service: |
---- | ---- | ||
- | <font 16px/ | + | **Necessary |
+ | **2. **Take off the left side cover of the boom. **a. **Press the ”button/ | ||
+ | **c.** Then lift the bottom part out a bit and now lift the cover straight up to detach. | ||
+ | | ||
- | <font 12pt/ | + | **4.** The outer narrower sliding plate is mounted with two screws underneath and the wider sliding plate is mounted with four screws underneath. |
- | + | ||
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | + | ||
- | <font 12pt/ | + | |
- | + | ||
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | + | ||
- | <font 12pt/ | + | |
- | + | ||
- | <font 12pt/ | + | |
{{: | {{: | ||
- | <font 12pt/ | + | **5.** Remove the screws on one sliding plate first. Make sure that you don’t lose any spring washers. If we don’t use spring washers, the screw will go through the sliding plate and hit the sliding rail directly. |
- | + | ||
- | * <font 12pt/ | + | |
- | + | ||
- | <font 12pt/ | + | |
- | | + | **a. **If it’s hard to get the old plates |
- | <font 12pt/ | + | **b. **If you remove |
+ | | ||
- | <font 12pt/ | + | **i.** The wider plate could be a bit more difficult to get out. If so, use the screwdriver from above after you pushed with it underneath and pull out the plate as much as you can. You could also bend the plate out with something pointed from the triangle formed corner |
- | | + | **7. **Mount the new sliding plate with wax. The track with the wax must be up against the sliding rail and outwards, towards |
- | <font 12pt/Arial,Helvetica, | + | |
- | <font 12pt/ | + | **8.** Mount the screws. Lift the sliding rail again, so we have as much space as possible |
- | <font 12pt/ | + | **:!: **<font 12pt/ |
- | | + | **9.** Now take the other sliding plate. **10.** Repeat step **5. 6. 7. **and **8.** **11.** Put the cover back on the boom. |
- | * <font 12pt/ | + | **b. **Push the bottom part inwards (against the boom). |
- | * <font 12pt/ | + | **c.** Push the cover backwards until it locks in. |