Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
service:service_instructions:sliding_plates_replacement [2020/07/03 01:50] – ↷ Page moved from service:service_instruction:sliding_plates_replacement to service:service_instructions:sliding_plates_replacement joachim | service:service_instructions:sliding_plates_replacement [2020/09/18 02:10] (current) – joachim | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Sliding plates replacement ====== | ====== Sliding plates replacement ====== | ||
- | This instruction will guide you on how to replace the sliding plates. | + | This instruction will guide you on how to replace the sliding plates. This instruction could also be used if you need to scrape you sliding plates or check the condition. |
- | Sliding plates are a wear part that needs to be replaced when symptoms occur. For how long one pair of sliding plates last is all idividual | + | Sliding plates are a wear part that needs to be replaced when symptoms occur. For how long one pair of sliding plates last is all individual |
- | For more detailed information regarding the sliding plates, go to exploded view: [[:telescope_assembly|Wide sliding plate]] and [[:middle_beam|Narrow sliding plate]]. | + | For more detailed information regarding the sliding plates, go to exploded view: [[:service: |
---- | ---- | ||
- | <font 16px/ | + | **Necessary |
- | <font 12pt/ | + | **1.** Start the robot. |
- | | + | * **a. **Place the boom horizontally. |
- | * <font 12pt/ | + | * **b. **Run the telescope out about 40 centimetres. |
- | * <font 12pt/ | + | * **c.** |
+ | **2. **Take off the left side cover of the boom. | ||
- | <font 12pt/ | + | |
+ | * **b. **While the ”button/hole” is held down, push the cover forward. | ||
+ | * **c. **Then lift the bottom part out a bit and now lift the cover straight up to detach. | ||
+ | **3.**Locate the current sliding plates**. ** | ||
- | | + | **4.**The outer narrower sliding plate is mounted with two screws underneath |
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | <font 12pt/ | + | **{{: |
- | <font 12pt/ | + | **5.** |
- | {{: | + | * **a.** If it’s hard to get the old plates out, you could dismount the plates on the sides/above as well for more space. |
+ | * **b.** | ||
+ | **6.** | ||
- | <font 12pt/ | + | |
+ | **7.** | ||
- | | + | **8.** Mount the screws. Lift the sliding rail again, so we have as much space as possible and it even helps to match up the screw with the screw holes. \\ :!: <font 12pt/ |
- | <font 12pt/ | + | **9.** |
- | | + | **10. **Repeat step **5. 6. 7.** and **8.** |
- | <font 12pt/ | + | |
- | <font 12pt/ | + | **11.** Put the cover back on the boom. |
- | + | * **a.** | |
- | * //<font 12pt/ | + | * **b.** |
- | <font 12pt/ | + | * **c.** |
- | + | ||
- | <font 12pt/ | + | |
- | + | ||
- | <font 12pt/ | + | |
- | + | ||
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |