Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
service:service_instructions:sliding_plates_replacement [2020/09/14 02:56] – user | service:service_instructions:sliding_plates_replacement [2020/09/18 02:10] (current) – joachim | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Sliding plates replacement ====== | ====== Sliding plates replacement ====== | ||
- | This instruction will guide you on how to replace the sliding plates. | + | This instruction will guide you on how to replace the sliding plates. This instruction could also be used if you need to scrape you sliding plates or check the condition. |
Sliding plates are a wear part that needs to be replaced when symptoms occur. For how long one pair of sliding plates last is all individual for each EVO Cleaner. It all depends on how heavy effected the telescope is in each program and how often the robot washes. | Sliding plates are a wear part that needs to be replaced when symptoms occur. For how long one pair of sliding plates last is all individual for each EVO Cleaner. It all depends on how heavy effected the telescope is in each program and how often the robot washes. | ||
- | For more detailed information regarding the sliding plates, go to exploded view: [[:telescope_assembly|Wide sliding plate]] and [[:middle_beam|Narrow sliding plate]]. | + | For more detailed information regarding the sliding plates, go to exploded view: [[:service: |
---- | ---- | ||
- | <font 16px/ | + | **Necessary |
- | <font 12pt/ | + | **1.** Start the robot. |
- | | + | * **a. **Place the boom horizontally. |
- | * <font 12pt/ | + | * **b. **Run the telescope out about 40 centimetres. |
- | * <font 12pt/ | + | * **c.** |
+ | **2. **Take off the left side cover of the boom. | ||
- | <font 12pt/ | + | |
+ | * **b. **While the ”button/hole” is held down, push the cover forward. | ||
+ | * **c. **Then lift the bottom part out a bit and now lift the cover straight up to detach. | ||
+ | **3.**Locate the current sliding plates**. ** | ||
- | | + | **4.**The outer narrower sliding plate is mounted with two screws underneath |
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | <font 12pt/ | + | **{{: |
- | <font 12pt/ | + | **5.** |
- | {{: | + | * **a.** If it’s hard to get the old plates out, you could dismount the plates on the sides/above as well for more space. |
+ | * **b.** | ||
+ | **6.** | ||
- | <font 12pt/ | + | |
+ | **7.** | ||
- | | + | **8.** Mount the screws. Lift the sliding rail again, so we have as much space as possible and it even helps to match up the screw with the screw holes. \\ :!: <font 12pt/ |
- | <font 12pt/ | + | **9.** |
- | | + | **10. **Repeat step **5. 6. 7.** and **8.** |
- | <font 12pt/ | + | |
- | <font 12pt/ | + | **11.** Put the cover back on the boom. |
- | + | * **a.** | |
- | * //<font 12pt/ | + | * **b.** |
- | <font 12pt/ | + | * **c.** |
- | + | ||
- | <font 12pt/ | + | |
- | + | ||
- | <font 12pt/ | + | |
- | + | ||
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |
- | * <font 12pt/ | + | |